
P/N 01807-001 Rev. B
MS Series Reader Quick Reference
This Quick Reference is designed for the experienced installer as a basic reference while
installing MS Readers to ensure all connections are made properly. For detailed information on
installing an MS Series Reader, see the MS-3000 Quick Start Guide
(P/N 01815-001), MS-4000
Quick Start Guide (P/N 01815-004), MS-5000 Quick Start Guide (P/N 01815-002), MS-7000
Quick Start Guide (P/N 01826-001), MS-9000 Quick Start Guide (P/N 01827-001).
1.0 Cable Requirements
1.1 MS-3000, MS-4000, and MS-5000
• up to 500 feet using six conductor, shielded, stranded AWG 24 wire (such as Belden
9536)
1.2 MS-7000
• up to 250 feet using six conductor, shielded, stranded AWG 24 wire
• up to 500 feet using six conductor, shielded, stranded AWG 20 wire
1.3 MS-9000
• up to 100 feet using six conductor, shielded, stranded AWG 24 wire
• up to 250 feet using six conductor, shielded, stranded AWG 22 wire
• up to 500 feet using six conductor, shielded, stranded AWG 18 wire
2.0 Grounding
Shield (Drain) continuity must run from the reader to the access panel. Shield (Drain) and
reader ground must be tied together at the access panel and connect to an earth ground in one
place.
3.0 Power
A reader may be powered by the access panel, so the reader is powered on when the access
panel is powered on. However the best case is to power the readers by a separate linear power
supply. When powered, verify the voltage at the reader meets the reader's requirements (refer to
Table 1 on page 3). When the reader is powered on, its beeper beeps in the following pattern: 3
short beeps, 1 long beep.
4.0 Operating Voltage
• MS-3000, MS-4000 operate using between 5v to 14v DC @ 50 mA
1
• MS-5000 operates using between 5v to 14v DC @ 100 mA
1
• MS-7000 operates using between 11v to 14v DC @ 200 mA
1
• MS-9000 operates using between 12v to 24v DC @ 200 mA
Figure 1: Earth Ground and Power Connections
Figure 2: PXL-250 Connection to 24VDC Power (used with MS-9000)
Figure 3: IntelliProx Connection to 24 VDC Power (used with MS-9000)
5.0 Reader Wiring
5.1 Connecting to the PXL-250 – TB5 or TB6
5.2 Connecting to the Design 5 PXL-100 – TB2
5.3 Connecting to the Design 5 PXL-100 – TB3
5.4 Connecting to the IntelliProx – TB1
6.0 Read Range
2
1. For best results, Keri recommends using 12 VDC on the MS-3000, MS-4000, MS-5000, and
MS-7000 readers.
Pin # Function
MS-4000
Wire Color
All Other MS
Readers Wire Color
1 Reader Antenna Blue Blue
2 Beeper – Green
3Reader Power Red Red
4 Reader Ground Black Black
4 Shield Silver Silver
5 Green LED – Brown
6 Red LED – White
7 no connection – –
Pin # Function
MS-4000
Wire Color
All Other MS
Readers Wire Color
14 Green LED – Brown
15 Beeper – Green
16 Reader Power Red Red
17 Reader Ground Black Black
17 Shield Silver Silver
18 Antenna Blue Blue
19 Red LED – White
Pin # Function
MS-4000
Wire Color
All Other MS
Readers Wire Color
20 Green LED – Brown
21 Beeper – Green
22 Reader Power Red Red
23 Reader Ground Black Black
23 Shield Silver Silver
24 Antenna Blue Blue
25 Red LED – White
Pin # Function
MS-4000
Wire Color
All Other MS
Readers Wire Color
1 Reader Antenna Blue Blue
2 Beeper – Green
3 Green LED – Brown
4 Red LED – White
5 Reader Power Red Red
6 Reader Ground Black Black
6 Shield Silver Silver
MS-3000 MS-4000 MS-5000 MS-7000 MS-9000
12 VDC 24 VDC
Cards 4 in. 1 in. 6 in. 14 in. 14.5 in. 18.5 in.
Tags 2 in. 1 in. 3 in. 7 in. 4.5 in. 9.5 in.
2. Read range may vary from what is shown depending upon the installation conditions, the
material on which the reader is mounted, and the age of the card or tag.
Commenti su questo manuale